Comments for Topcoat Review

Comment on Wood. by Staining Oak - Topcoat Review : Topcoat Review

Staining Oak - Topcoat Review : Topcoat Review — Tue, 21 May 2013 07:08:07 +0000

[...] are far more challenged by fine stain grade systems than paint. And there is no doubt that wood finishing is misunderstood, even by professional [...]

Comment on Graco 9.5 Fine Finish hvlp with Turboforce by Graco Edge Gun and 9.5 Turboforce HVLP : Topcoat Review

Graco Edge Gun and 9.5 Turboforce HVLP : Topcoat Review — Tue, 21 May 2013 06:57:43 +0000

[...] have been running the Graco 9.5 Finish Pro hvlp pretty hard for well over a year now both in the shop and on site in the field. This week, we [...]

Comment on Ipe Deck Finish: 5 things not to do by Scott Burt

Scott Burt — Tue, 21 May 2013 06:31:34 +0000

Do not spray it, Christopher. For many reasons, which would be enough to write another whole article about. For application, brushing the oil on is best, and then wiping off any excess oil that does not penetrate the wood, within 15-20 minutes. Depending on the length of your deck, and the pace at which you work, this may mean brushing 3-6 courses at a time, and then going back to wipe off excess. Just don’t get so far ahead of yourself that you can’t reach back to where you started, because you definitely don’t want to walk on the wet oil. Hope this helps.

Comment on Ipe Deck Finish: 5 things not to do by Christopher Jacobs

Christopher Jacobs — Tue, 21 May 2013 04:06:07 +0000

I am pretty handy with a spray gun. Can I spay on Penofin Marine Grade Oil on my Ipe deck or is there a more preferred way to apply it. If there is a more preferred way, could you give details of this application procedure?

Comment on Titan ProTouch Handheld Cordless Airless Sprayer Review (2011) by Titan 440 Multi Finish Testing at Topcoatreview.com : Topcoat Review

Titan 440 Multi Finish Testing at Topcoatreview.com : Topcoat Review — Mon, 20 May 2013 20:30:36 +0000

[...] sprayers from as many competitive manufacturers as possible. Readers may recall our review of the Titan ProTouch during our cordless sprayer series last year. We appreciate Titan participating in our air assisted [...]

Comment on Sherwin Williams ArmorSeal Epoxy Coating by Scott Burt

Scott Burt — Mon, 20 May 2013 11:29:13 +0000

It really is a bulletproof coating. Glad to hear it is doing so well in such a harsh environment. We have used it in warehouse/distribution center applications with the same results.

Comment on Ben. by Scott Burt

Scott Burt — Mon, 20 May 2013 11:26:59 +0000

Sounds frustrating, Doug, but my guess would be that it can be resolved with an additional coat in areas where there is bleed through. Just curious, did your painter pole sand the walls prior to applying the new paint? Sometimes this helps to dull the previous color and create better adhesion for the new coats, so they can be applied to the full recommended thickness.

Comment on Ipe Deck Finish: 5 things not to do by Scott Burt

Scott Burt — Mon, 20 May 2013 11:24:43 +0000

Hello Christopher,

What product was used on the faces when it was finished upon installation? This may effect some aspects of my answers below, but generally:

1. It’s not too late. If you are up to the task, it’s cheap insurance to help prevent cupping.
2. You should use a penetrating oil with transoxide pigments, such as Penofin Marine Grade Oil or Armstrong Clark.
3. Yes. The boards are most stable when they have the same type of coating all the way around. From the topside and bottom, be sure to get the side edges of the boards as best you can so that all edges are sealed.

Comment on Sherwin Williams ArmorSeal Epoxy Coating by Doug Parsons

Doug Parsons — Mon, 20 May 2013 10:34:07 +0000

I used this product on a Bobcat location in Virginia Beach. It was a remodel. This is the best product I have ever seen. It was applied over a year ago, and it is still holding up in both shine, and durability. It resist penetration from Hydraulic fluid, and most harsh chemicals. As the author said it should only be applied by a professional.

Comment on Ben. by Doug Parsons

Doug Parsons — Mon, 20 May 2013 10:28:47 +0000

We just used this paint on a kitchen remodel. My painter applied to coats of semi gloss, white over an antique white (walls/ceilings). The coverage was terrible. I still have bleed through. The store agent gave him white tint 1x, (without any tint, just white) to match the white cabinets. I have called the Ben Moore store, and they are going to send a rep out to check it out.